The Blog

SpeTool CNC Bits 16% Discount Code: SALE

SpeTool CNC Bits 16% Discount Code: SALE

Welcome Back! I've worked with SpeTool a new CNC Bit Supplier to provide the SethCNC YouTube community a 16% discount using the coupon code: SALE Check Out there newest Bit Selection here: https://bit.ly/3s5tVvz   My Favorite Bits from SpeTool are their Tapered Ball Bits, they perfect for 3D relief carvings: https://bit.ly/3lYBmkb       SpeTool WD-2 Router Bits Set https://spetools.com/collections/router-bits-set/products/spetool-cnc-router-bits-carving-8-pcs-set-for-wood-detail-profile-v-groove-engraving-solid-carbide-1-4-inch-shank?ref=SALE&variant=40456773697719

Read more →


CNC Error and Alarm Codes

CNC Error and Alarm Codes

                  Error Code Error Message Error Description 1 Expected Command Letter G-code words consist of a letter and a value. Letter was not found. 2 Bad Number Format Missing the expected G-code word value or numeric value format is not valid 3 Invalid Statement Grbl ‘$’ system command was not recognized or supported. 4 Value < 0 Negative value received for an expected positive value. 5 Homing Disabled Homing cycle failure. Homing is not enabled via settings. 7 EEPROM Read Fail An EEPROM read failed. Auto-restoring affected EEPROM to default values. 8 Not Idle Grbl ‘$’...

Read more →


Carveco Launches new Training Portal

Carveco Launches new Training Portal

NEW CARVECO TUTORIAL PORTAL November 5, 2021 Carveco launched a new portal to host all of their Training Materials for Carveco Maker and Carveco Maker Plus. The old location had become a bit laggy due to the complexities of hosting so much media content and they moved their entire Training regiment over to this page: NEW CARVECO TUTORIAL PORTAL         Interested In Carving 3D like this?   Try for free with this link: 90 days of Carveco Maker FREE SpeTool WD-2 Router Bits Set

Read more →


Sainsmart Genmitsu PROVerXL 4030 and 6060 Default GRBL Settings

Sainsmart Genmitsu PROVerXL 4030 and 6060 Default GRBL Settings

These are the default GRBL settings for the SainSmart Genmitsu PROVerXL 4030 with notes for the extended 6060 differences.      To Learn More about the 6060 Extension Kit CLICK HERE>>>    To View and Change your Settings In Easel Select Machine > General Settings > Machine Inspector    ( OR simply Press Ctrl+Shift+D ) Then scroll to the bottom portion labeled "settings" if any need changed, scroll to the top "console" section and enter them one at a time as needed. $0=10 (Step pulse time)$1=25 (Step idle delay)    *Best practice is to set this to 255$2=0 (Step pulse invert)$3 = 0 (dir...

Read more →


Bobs Evolution 4 default GRBL settings

Bobs Evolution 4 default GRBL settings

To View and Change your Settings In Easel Select Machine > General Settings > Machine Inspector    ( OR simply Press Ctrl+Shift+D ) Then scroll to the bottom portion labeled "settings" if any need changed, scroll to the top "console" section and enter them one at a time as needed. $0=5 (Step pulse time)$1=255 (Step idle delay)$2=0 (Step pulse invert)$3 = 0 (dir port invert)$4 = 0 (step enable invert, bool)$5 = 1 (limit pins invert, bool)$6 = 0 (probe pin invert, bool)$10 = 1 (status report)$11 = 0.010 (junction deviation, mm)$12 = 0.002 (arc tolerance, mm)$13 = 1 (report inches, bool)$20 = 1...

Read more →