The Default GRBL Settings for the Silverback 6060 with differences for the larger 1Mx1M (39"x39") model shown in RED
To View and Change your Settings In Easel Select Machine > General Settings > Machine Inspector ( OR simply Press Ctrl+Shift+D )
Then scroll to the bottom portion labeled "settings" if any need changed, scroll to the top "console" section and enter them one at a time as needed.
$0=10 (Step pulse time)
$1=255 (Step idle delay)
$2=0 (Step pulse invert)
$3=0 (Step direction invert) (NOTE - do not change this value if your machine movement is correct; this may vary for your machine, you can perform the Easel Machine Setup and this setting will be automatically adjusted by testing and answering the questions about whether its operating correctly for each axis.)
$4=0 (Invert step enable pin)
$5=0 (Invert limit pins)
$6=0 (Invert probe pin)
$10=115 (Status report options)
$11=0.010 (Junction deviation)
$12=0.002 (Arc tolerance)
$13=0 (Report in inches)
$20=0 (Soft limits enable)
$21=1 (Hard limits enable)
$22=0 (Homing cycle enable)
$23=3 (Homing direction invert)
$24=25.000 (Homing locate feed rate)
$25=500.000 (Homing search seek rate)
$26=250 (Homing switch debounce delay)
$27=3.000 (Homing switch pull-off distance)
$30=10000 (Maximum spindle speed)
$31=0 (Minimum spindle speed)
$32=0 (Laser-mode enable)
$100=200.000 (X-axis travel resolution) **The very first batch of SilverBacks used 10mm lead screws and these values: $100=160.000
$101=200.000 (Y-axis travel resolution) **The very first batch of SilverBacks used 10mm lead screws and these values: $101=160.000
$102=160.000 (Z-axis travel resolution)
$110=2000.000 (X-axis maximum rate)
$111=2000.000 (Y-axis maximum rate)
$112=2000.000 (Z-axis maximum rate)
$120=300.000 (X-axis acceleration)
$121=300.000 (Y-axis acceleration)
$122=300.000 (Z-axis acceleration)
$130=600.000 (X-axis maximum travel) $130=1000.000 (1010 Setting)
$131=600.000 (Y-axis maximum travel) $131=1000.000 (1010 Setting)
$132=55.000 (Z-axis maximum travel)
$1=255 (Step idle delay)
$2=0 (Step pulse invert)
$3=0 (Step direction invert) (NOTE - do not change this value if your machine movement is correct; this may vary for your machine, you can perform the Easel Machine Setup and this setting will be automatically adjusted by testing and answering the questions about whether its operating correctly for each axis.)
$4=0 (Invert step enable pin)
$5=0 (Invert limit pins)
$6=0 (Invert probe pin)
$10=115 (Status report options)
$11=0.010 (Junction deviation)
$12=0.002 (Arc tolerance)
$13=0 (Report in inches)
$20=0 (Soft limits enable)
$21=1 (Hard limits enable)
$22=0 (Homing cycle enable)
$23=3 (Homing direction invert)
$24=25.000 (Homing locate feed rate)
$25=500.000 (Homing search seek rate)
$26=250 (Homing switch debounce delay)
$27=3.000 (Homing switch pull-off distance)
$30=10000 (Maximum spindle speed)
$31=0 (Minimum spindle speed)
$32=0 (Laser-mode enable)
$100=200.000 (X-axis travel resolution) **The very first batch of SilverBacks used 10mm lead screws and these values: $100=160.000
$101=200.000 (Y-axis travel resolution) **The very first batch of SilverBacks used 10mm lead screws and these values: $101=160.000
$102=160.000 (Z-axis travel resolution)
$110=2000.000 (X-axis maximum rate)
$111=2000.000 (Y-axis maximum rate)
$112=2000.000 (Z-axis maximum rate)
$120=300.000 (X-axis acceleration)
$121=300.000 (Y-axis acceleration)
$122=300.000 (Z-axis acceleration)
$130=600.000 (X-axis maximum travel) $130=1000.000 (1010 Setting)
$131=600.000 (Y-axis maximum travel) $131=1000.000 (1010 Setting)
$132=55.000 (Z-axis maximum travel)
Check out this Laser And Dust Shoe Add-On for your Silverback:
My Favorite V-Bits:
Interested In Carving 3D like this?
Try for free with this link: 90 days of Carveco Maker FREE
YoraHome SilverBack 6060 1010 1mx1m 39x39